10 Common Embroidery Machine Problems & How To Fix Them

In the daily production order process, it is inevitable that the computer embroidery machine will fail inevitably. Today, Eagle Digitizing has a summary of 10 types of computer proof.

1. Computer embroidery processing break

The wool is actually very different from the disconnection. Basically, there is a burr on the surface of the rotation "Putting off the slide with fine sandskin" or the needle position. If it is still not done, it is a big problem. Pay attention to the rotation when you look at whether the needle is in the center of the needle board. If it has been tilted to the needle plate, the basic needle plate hole has been hairy. There is no top to the upper end of the needle rod. "What do you say about this wool? Simply and simple to say is not simple. It is really not easy. Go to experience by yourself.

2. The computer's embroidery is not available for parking

Go first, if you click it, it will be OK. Then I do n’t know what the problem is. My 02 computer is the problem. If it ’s still not in place, it shakes down the machine with your hand heavy. If the machine repeats the scale, whether the scale is always heavy or shook, those who press all over the feet will be pressed to see if there is any machine head to press. If you can't move, the slider is short of oil. If you can still turn it on, it is the lack of oil in the head of the machine. The solution is to touch the back of the rack to see which one is fever. If you can't touch it, you can only let the machine run, and listen carefully to judge.

3. Computer embroidery processing is abnormal

There are abnormalities in computer embroidery machines. It mainly includes insufficient color replacement, no color replacement, more limited color replacement, two seconds of color replacement, and abnormal color changes.

When the color replacement is abnormal, you can first reduce the connection of the connectors on the power board to be firmly connected, and then check whether the melting line on the power board is fused. If the fuse is broken, it needs to be replaced. The clockwise replacement occurs, and the inspection method is as follows without changing color or opposite. For the needle abnormality, you can use a wrench to move the color replacement of the color change to the color.

Computer embroidery processing color timeout to rotate the color change case with No. 8 wrench. Look at the pressed foot, the jumping pole is abnormal. If it is normal, press the head of each machine by hand, and see if the slider is killed. Turn several times before and after the wrench, and use more force to see which head has a severe jitter. If you can easily turn the coloring box, then use the computer to change the needle position to see if it is too much to change the color. Solution, remove the panel next to the color change box, and adjust the color change angle.

4. Computer embroidery processing pattern

If the vehicle often appears in the same position to run the pattern, see if there is an outspoken screw around the frame, or look at the raised things. If normal, despise the framework to see if there is any deformation, such as deformation is that the teeth of the guide strap under the deformation have been deformed.

5. The position of the computer embroidery machine is abnormal

1). The gap between the machine embroidery needle and the spin shuttle needs to be re -adjusted to the corresponding position;

2). Check whether the tip of the spin shuttle is blunt or defective, repair the spike and polish;

3). The embroidered noodles are too loose, and you need to tighten the embroidered fabric;

4). The pressure of the embroidered foot spring is insufficient or damaged. You need to adjust the embroidered flower feet spring.

6. The situation of the random alarm is on the vehicle when the car is 1-2 stitches.

For this situation, please check whether the head lines are short -circuited.

7. The bulls do not cut the line.

In this case, the situation was adjusted to die.

8. Falling and cutting the bottom line

Replace the motherboard in this situation.

9. There are abnormal noises from the position of the thread -cut knife card

This situation replaces the reasons for the positioning point of Dahao Electric Control checkpoint.

10. The computer embroidery is turned on the red light during processing

In this case, check whether there is a problem with the motherboard, and check the potentiometer.